Sandeep's email address and phone number have been validated.
Sandeep
- Rate ₹600
- Response 1h
₹600/hr
More Electronics teachers
Unfortunately, this teacher is not available
- Electronics
- Automation
Programming in Assembly language and Embedded C for 8051 controller. Schematic drawing with express pcb software
- Electronics
- Automation
Class location
About Sandeep
I am consultant in the field of embedded system design. Project Guidance provided to almost 600 E & TC students so far. Interested in teaching application development logic and interaction of hardware and software. Did my own pcb design and circuit design. I am using Express PCB software.
See more
About the class
- BTech
- Adult Literacy
- Undergraduate
- +3
levels :
BTech
Adult Literacy
Undergraduate
Masters
PG Diploma
Other
- English
- Hindi
- Marathi
All languages in which the class is available :
English
Hindi
Marathi
Examples programs are prepared by selecting commonly used instructions in Assembly language.
Example program in C is prepared for LCD (16x2 alphanumeric Display)
Interaction of hardware and software is shown on a DEVICE. This is very useful for application development. A small application is prepared for each example program.
The DEVICE has built in hardware for 8051 controller and Graphic Display. Program is shown on graphic display while functioning and voltages can be measured on hardware.
Following programs are available for demonstration.
(Programs from Sr. no 1 to 15 are in assembly language and Sr. 16 is in Embedded C)
1) Introduction (free lecture)
2) Switch and LED
3) Switch and LED with conditional branching
4) Switch and LED with delay routine
5) Switch and LED with large delay
6) CJNE Instruction
7) JBC Instruction
8) RR (rotate right) Instruction
9) Indirect addressing with R0
10) SWAP Instruction
11) External Interrupt 0
12) Packed BCD and ASCII
13) Delay with Timer 0
14) Timer 0 interrupt
15) Writing on LCD (16x2 alphanumeric Display)
16) Writing on LCD (16x2 alphanumeric Display) using C program
All above programs need @15 minutes for explanation.
Once you have command on programming then you should get target board,PC ,flash programmer etc for hands on experience.
See more
Rates
Rate
- ₹600
Pack prices
- 5h: ₹3000
- 10h: ₹6000
online
- ₹600/hr
Details
Price will be Rs 150 per example program
Sandeep 's video
Similar Electronics teachers in Pune
Suhas
Pune & Online
- ₹400/hr
- 1st class free
Smita
Pune & Online
- ₹800/hr
- 1st class free
Rajashri
Pune & Online
- ₹800/hr
- 1st class free
Sanjeev
पुणे & Online
- ₹800/hr
- 1st class free
Ritesh
Pimpri-Chinchwad & Online
- ₹1,600/hr
- 1st class free
Arun
Pimpri-Chinchwad & Online
- ₹400/hr
- 1st class free
Indrayani
Pimpri-Chinchwad & Online
- ₹500/hr
- 1st class free
Sandeep
Howrah & Online
- ₹1,499/hr
- 1st class free
Pallabi
Bengaluru & Online
- ₹1,200/hr
CHARUU ROHIT
New Delhi & Online
- ₹149/hr
- 1st class free
Shilpa
Fazilka & Online
- ₹399/hr
- 1st class free
Janaki
Bengaluru & Online
- ₹500/hr
- 1st class free
Harshit
Noida & Online
- ₹999/hr
- 1st class free
Arvindh
Chennai & Online
- ₹800/hr
- 1st class free
Sarbani
Durgapur & Online
- ₹1,000/hr
DrNishant
Bengaluru & Online
- ₹1,000/hr
- 1st class free
Usharani
Nagondapalli
- ₹1,500/hr
- 1st class free
Nikhat
New Delhi & Online
- ₹1,000/hr
- 1st class free
Prabha
Thuraiyur & Online
- ₹300/hr
- 1st class free
Veena
Ernakulam & Online
- ₹350/hr
- 1st class free
-
More Electronics teachers
